Kubota Service Repair Manuals. Error Codes

KUBOTA SERVICE AND WORKSHOP MANUALS

2WD

4WD

API

ASABE

ASTM

DIN

DT

fpm

Hi-Lo

HST

m/s

PTO

RH/LH

 

ROPS

rpm

r/s

SAE

SMV

 

2-Wheel Drive

4-Wheel Drive

American Petroleum Institute

American Society of Agricultural and Biological Engineers, USA

American Society of Testing and Materials, USA

Deutsches Institut für Normung, GERMANY

Dual Traction [4WD]

Feet Per Minute

High Speed-Low Speed

Hydrostatic Transmission

Meters Per Second

Power Take Off

Right-hand and left-hand sides are determined by facing in the direction of forward travel

Roll-Over Protective Structures

Revolutions Per Minute

Revolutions Per Second

Society of Automotive Engineers, USA

Slow Moving Vehicle


Download
B2301 B2601 Workshop Service Manual.pdf
Adobe Acrobat Document 8.1 MB
Download
B6000 Operators Manual.pdf
Adobe Acrobat Document 10.5 MB
Download
BX1860 BX2360 BX2660.pdf
Adobe Acrobat Document 16.1 MB
Download
B5100_B7100__service_manual_part1.pdf
Adobe Acrobat Document 7.1 MB


Error Codes

CAN system error / Problem / Solution

E:001 The Controller Area Network (CAN) has developed a fault. Measured values may be incorrect and switches may not function.

The machine can be started and driven. Do not perform any work with the machine.

E:005 The temperature of the coolant is higher than normal.

Operate the machine only with reduced loads until the temperature is normal again.

E:014 The engine oil pressure is too low.

Stop the engine immediately. The engine may have developed a fault.

Inform your KUBOTA dealer immediately.

E:015 The machine is overheated and must cool off by idling.

Allow the machine to cool off by idling. Do not switch the engine off as the coolant could then boil over.

Clean the radiator and check the coolant. Refi ll the radiator with coolant by its boiled-over amount. Unclog the radiator and other components before use again. Check also the hydraulic system for oil leak and other troubles. If an oil leak is found, immediately contact your local dealer for repair.

E:016 The charging system has developed a fault.

Check the V-belt. When the V-belt is OK, let the engine run until the indicator goes out.

If the indicator does not go out, inform your KUBOTA dealer immediately.

E:017 The fuel sensor has developed a fault; the fuel gauge does not appear in the display.

Press the display selector switch to return to the default display.

E:018 The coolant temperature sensor has developed a fault; the coolant temperature gauge

does not appear in the display.

Press the display selector switch to return to the default display. The functions of the machine

are stable but overheating cannot be excluded.

E:020 The electrical system in the lock lever (unload lever) has developed a fault.

The engine can be started but the machine cannot be set in motion.

E:021 The electrical system in the travel speed has developed a fault.

The machine can only be set in motion at low speed.

E:025 This is a warning that a higher volt- age (from a 24-V battery, for example) is being applied to the electric circuit, or that there is a problem with the alternator.

Switch the engine off immediately and check the battery and the alternator. Restart the engine.

E:027 The 5-V sensor supply line has de- veloped a system fault. The main functions are not available.

The machine can be started and driven. Do not per- form any work with the machine.

E:028 The 12-V sensor supply line has de- veloped a system fault. The main functions are not available.

The machine can be started and driven. Do not per- form any work with the machine.

E:029 This error code indicates a step in a procedure.

Start the engine; the indicator goes out.

Comments: 4
  • #4

    Kelum (Sunday, 23 July 2023 02:08)

    Error cords mening pdf please

  • #3

    marcel geverink (Saturday, 31 December 2022 01:11)

    what causes the code p 00 93 and p 2108 thanks

  • #2

    CARL KERNAN (Friday, 21 October 2022 15:46)

    WHAT CAUSES THE CODE PO539

  • #1

    Larry (Wednesday, 06 October 2021 21:58)

    En9
    Error code